Hotpoint CT NTC IW0 Bedienungsanleitung PDF herunterladen (Seite 12)

hotpoint.eu

C10

Removetheltercartridgefromtheheadby

pulling it out as per illustration.

The lter cartridge can be disposed of

with normal household waste.

Before installing the new ltering car-

tridge, wash the plastic lter body with a

washing up liquid and rinse thoroughly.

C11

Remove the new lter cartridge from the

packagingandtitbyrmlypushingitintothel-

terhead,makingsureitisrmlyandsecurelyt-

ted.Makesurethenewlteryouarettingcomes

in a sealed bag for hygienic purposes.

C12

Screwthelterheadandthelterbodyto-

gether,makingsureitisrmlytightened.

C13

Fitthelterassemblywiththebackintothe

appliance as follows:

1. Insertthelterassemblybackintoitscradle,

aligning the two male spigots with the female

holesinthecradle.Pushrmlyuntilthelter

sitssnuglyandisushinsidethecradleand

with the cradle top surface.

2. Lockthelterbyclosingthelockingleverun-

tilit‘clicks’intoplace

3. Rotate the red rotating lever back into the

LOCK position.

C14

Re-tthelid,makingsurethefrontisatta-

chedrst.Ifthelidisnotttedcorrectlytheunit

will not switch on.

Fit the lid making sure the front is

pushed in place rst and then push the

back end with the screws down to give a snug

t.

C15

Re-tthetwoscrewsthatholdtheliddown

using the screwdriver.

The screws should be hand tightened,

do not over tighten.

C16

Insert the plug into the mains socket and

press and hold the dispense button for 10 secon-

dsuntilyouhearabeepasthiswillresetthelter

timer.

and pulling it up.

ToremovetheUVlamprmlypullitupand

out. Do not pull the lamp out at an angle as it may

breakordamagetheinternalpartsoftheapplian-

ce.

The UV lamp must be disposed of cor-

rectly and must not be disposed of with

normal household waste.

Insert the new UV lamp while holding the

white end caps only. Insert the UV lamp as shown

in the illustration and push it all the way down until

it cannot go any further.

Do not use force when removing and in-

serting the UV lamp as you may damage

internal parts. Do not touch the UV lamp glass

surface with your ngers as this will affect the

performance of the UV lamp.

Re-connecttheUVlampconnectormaking

sure the connectors are lined up correctly as they

willonlyttogetherwhencorrectlyaligned.

Pay attention not to wet the UV lamp

connector; in case of water drops on UV

lamp connectors, do not reconnect to power

mains before drying completely.

Wear disposable gloves during the ope-

rations of lter removal hereafter descri-

bed to avoid the direct contact with wet parts.

To remove the Filter, do the following:

1. Rotate the red rotating lever so that it is pa-

rallel with the side panel.

2. Insertyourngerintotheroundholeofthe

lever, and pull the lever up to the vertical

position.

3. Pull the lever straight up to remove the Filter

assembly (some slight force may be requi-

red).

Unscrewthelterbodyfromthelterhead

byturningthebaseinaanticlockwisedirectionas

per the illustration.

Be careful as the lter body will contain

water.

1 2 ... 7 8 9 10 11 12 13 14 15 16 17 ... 60 61

Kommentare zu diesen Handbüchern

Keine Kommentare

Hotpoint CT NTC IW0 Bedienungsanleitung Seite 12

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Nein Hotpoint CT NTC IW0