Hotpoint TCD 971 6CY1 (EU) Bedienungsanleitung PDF herunterladen (Seite 14)

The Controls

! Warning, after pressing the START/PAUSE button ,

the programme cannot be changed. To change a selected

programme, press the START/PAUSE button

the light

flashes Amber to indicate the programme is paused. Select

the new programme and any options required, the light will

then flash green. Press the START/PAUSE button

again

and the new programme will start.

• Option buttons

These buttons serves to personalise the selected

programme according to personal requirements.

Not all options are available for all programmes.

Some options are incompatible with the ones

previously set. If the button of any unavailable option

is pressed, the buzzer will beep 3 times. If the option

is available, the option light will stay on.

Delay Timer (Time Delay)

The start of some programmes (see The Display and

Programmes tables) can be delayed for up to 24 hours.

Ensure the water container is emptied before setting a

delayed start.

Crease Care

The pre-care option is only available if a delayed start has

been selected. It tumbles the clothes occasionally during

the delayed period to help prevent creases developing. The

post-care option occasionally tumbles the clothes after end

of the drying and cool tumble cycles to prevent creases

developing, should you not be available to remove the load

immediately the programme is complete

Note: The START/PAUSE

light flashes Amber during

this phase. Selecting this option enables both the pre and

post care functions if appropriate.

Heat Level button, Display and Icons

Not all programmes allow you to change the heat level and

some programmes allow all three heat level options:

Low, Medium and High.

When the heat level options are available pressing this

button changes the heat level and the display briefly shows

the selected heat level, along with a display of the selected

level icon:

HIGH HEAT

MEDIUM HEAT

LOW HEAT

Extra Care

This Anti-Ageing function for Cottons helps to maintain the

brightness of your laundry for a long time, thanks to the

correct drum rotation (reduced in the last part of the cycle)

and the correct temperature.

Less Tangled

This option has the drum movement modified to give a

tumbling action that reduces tangling and knotting of your

clothes. The Less Tangled option gives best results when

used with smaller loads.

Ready to Iron

This option allows you to dry loads where only some of the

items need ironing and you do not wish to fully dry those

items. When Iron Dry level is reached, a buzzer sounds to let

you know that the items that need ironing can be removed.

The dryer then stops and the START/PAUSE light flashes

orange. Remove the items you wish to iron, close the

door and press the START/PAUSE button

, the dryer

continues until the remaining items reach the selected dryness

level. It can be used for load sizes up to 3kg.

• TIME DISPLAY

The display shows either the amount of time delay remaining or

an indication of the amount of time left for a drying programme

(see The Display). The display also shows if there is a problem

with your dryer, if this occurs the display will show F followed by

a fault code number (see Troubleshooting).

• Empty Water Container

(Messages about emptying can be ignored if you have plumbed

your dryer into a drain as there is no need to empty the water

container). Messages are displayed to reminds you to empty

the water container (see The Display). If the water container fills

during a programme, the heater turns off and the dryer does a

period of Cool Tumble. After this it stops and a message tells

you to

EMPTY THE WATER CONTAINER

. You must empty the water

container and restart the dryer or the clothes will not dry. After

re-starting the dryer the message will take a few seconds to go

out. To avoid this always empty the water container each time

you use the dryer (see Maintenance).

• Door Opening

Opening the door during a programme will stop the dryer and

have the following effects:

Note: The START/PAUSE

light flashes Amber during the

Post Care phase of a programme

 • The display shows

PAUSED

• During a delay phase the delay will continue to count down.

The START/PAUSE

button must be pressed to resume

the delay programme. The display will change to show current

status.

• The START/PAUSE

button must be pressed to resume

the programme. The display will change to show the

current status.

• During the Post Care phase, the programme ends. Pressing

the START/PAUSE

button will restart a new programme

from the beginning.

• Note

If you have a power cut, switch off the power or remove the

plug. When power is restored, press and hold the On/Off

button until the display briefly shows

POWER ON

and the dryer

reactivates. Then press the START/PAUSE

button and the

programme will resume.

1 2 ... 9 10 11 12 13 14 15 16 17 18 19 ... 47 48

Kommentare zu diesen Handbüchern

Keine Kommentare

Hotpoint TCD 971 6CY1 (EU) Bedienungsanleitung Seite 14

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Nein Hotpoint TCD 971 6CY1 (EU)